Choose the main color theme for your bathroom, but it should depend on the existing color of the wall. For example, for white colors, apply the white color on all over the walls and furniture. But to keep the contrast, apply a bit darker color for your flooring. You can do it by having a cheaper tile stamp to get the floral or another exciting pattern.

A DIY bathroom remodel is a big project. If you can only work weekends, your bathroom will be out of commission for two months or more. You’ll need all your expertise as an experienced do-it-yourselfer because you’ll have to tackle electrical, plumbing, tiling, drywalling, taping and even exterior siding. In this DIY shower remodel article, we’ll deal mostly with the nuts and bolts of ripping out existing plumbing and replacing it correctly with new, easily installed PVC piping.
When you use a bold accessory like an animal skin, you need to make sure that it isn't lost in a bunch of other decor elements. This bathroom uses its neutral, modern design to really give space to the zebra skin rug here. And the great thing about this kind of design is that you can change this one decor element as often as you wish, without having to spend thousands remodeling every time.
Tear out the existing piping (Photos 5 and 6). Then frame the 2×6 walls that will contain the new plumbing and the opposite end of the shower base (Photos 8, 9 and 14). It’s easiest to nail the bottom plate to the floor and the top plate to the ceiling, then fill in the studs one at a time by toenailing them in at the top and bottom. Stack the studs directly in front of the old ones wherever possible. Space the studs in the center of the shower about 12 in. apart to leave room for the shower valve and showerhead. The studs behind the toilet should be spaced exactly 19-3/4 in. apart for securing this toilet chair carrier (Photos 8 and 15).

The wall-hung toilet’s supply line must have a male adapter with a temporary galvanized cap. Check the instructions on the toilet to get the proper location. Routing water supply lines is different in every bathroom, so you’ll have to adapt runs to your situation. But run the plastic drain lines and vents before starting any supply work. It’s much easier to route water supply lines around drain lines than to route drains and vents around supply lines. The same thinking applies to electrical work: Wait until the water supply work is finished before wiring.
The average bathroom remodel costs $10,445 Most homeowners spend between $5,975 and $14,927. You can spend as little as $3,500 to $7,000 updating the essentials in a small or medium-sized bathroom. On a large or master bath, you could spend $25,000 or more. Labor averages 50 percent of the total project price at about $65 per hour. Expect pricing to vary regionally up to 20 percent due mainly to labor. Material prices stay roughly the same across the country.

Preassemble the shower valve by soldering copper nipples and the shower supply pipe to male adapters and screwing them into the shower valve before fastening the valve to the blocking. That way you won’t damage the valve with heat from the soldering torch. Mount the valve 36 in. above the floor. You can mount the showerhead at any height, but plumbers typically mount them 6 ft. 6 in. above the floor.
Great tips. At the onset of explaining various causes of a squeak, Tom Silva says it can be alignment, either of the door-to-hinge, or hinge-to-hinge. Hmm, seems to me those two scenarios different than the case in the vid, that being singular hinge with the barrels out of alignment. So, the vid shows a great solution to fixing out of alignment barrels, but what about fixing doors with hinges out of alignment from each other, or hinges out of alighment on the door? How do you make that determinations, and what is the solution? thx
The tank is concealed within a 2×6 wall that’s built in front of the existing plumbing wall. It does require some plumbing rerouting because the waste line runs through the wall instead of the basic floor-mounted toilet flange (see Photos 8 – 12). The toilet can be ordered with a wall-mounted access panel/flush button like ours or with the panel mounted on top of a half wall. A ‘chair carrier’ (Photo 11) comes with the toilet. This steel framework contains the toilet and operating mechanisms and is designed to support the weight of the toilet.
Don't lay tile over plywood, which can swell with moisture and break the tile bond. If you're not pouring a new floor, mortar and screw ¼-inch backerboard over a level subfloor, then lay tile on top. Another option: Put in a DITRA flexible underlayment, which helps prevent cracks in ceramic and stone tile by evenly distributing the weight they carry.
Interior bathroom demolition costs $1,000 to $2,300. Prices can go higher if you’re removing and moving walls to create a different footprint. For the experienced DIYer, this is a good place to save money by doing it yourself or assisting the contractor. However, demo can get expensive quickly if you take out a load bearing wall, cut electrical lines or break a water pipe. Avoid the risk by hiring a pro.
×