Great tips. At the onset of explaining various causes of a squeak, Tom Silva says it can be alignment, either of the door-to-hinge, or hinge-to-hinge. Hmm, seems to me those two scenarios different than the case in the vid, that being singular hinge with the barrels out of alignment. So, the vid shows a great solution to fixing out of alignment barrels, but what about fixing doors with hinges out of alignment from each other, or hinges out of alighment on the door? How do you make that determinations, and what is the solution? thx
If your room is wider than the shower base, fur in the walls as needed to butt against the ends of the shower base (see Photo 14). Our bathroom is 6 ft. wide, so we added a floor-to-ceiling 2×6 wall at the showerhead end and a shorter 2×6 wall at the opposite end. We made that wall only 43 in. above the floor so we could use the top of the wall to hold shampoo and other shower supplies. The shower base usually comes with a special 2-in. drain fitting that you connect to the drain line (Fig. B).
Preassemble the shower valve by soldering copper nipples and the shower supply pipe to male adapters and screwing them into the shower valve before fastening the valve to the blocking. That way you won’t damage the valve with heat from the soldering torch. Mount the valve 36 in. above the floor. You can mount the showerhead at any height, but plumbers typically mount them 6 ft. 6 in. above the floor.
Using the ultra-trendy animal skull as a main focus point, this space definitely stands out from the rest of the usual white and boring contemporary bathrooms. Notice how the tiny, delicate bare branch echoes and contrasts the strong antlers on the wall, and how the pendant light hangs right in the middle of the negative space provided by the antlers.
Don't lay tile over plywood, which can swell with moisture and break the tile bond. If you're not pouring a new floor, mortar and screw ¼-inch backerboard over a level subfloor, then lay tile on top. Another option: Put in a DITRA flexible underlayment, which helps prevent cracks in ceramic and stone tile by evenly distributing the weight they carry.
The Home Depot is a great place to buy your bathroom essentials and remodeling materials. We also provide top-rated design and installation services for homeowners across America. Besides undergoing full background checks, our hand-selected remodeling experts are local, licensed and insured. The Home Depot also offers a great selection of flexible finance options.
Bathroom remodels provide 60 to 70 percent resale returns as a home improvement project. However, this project isn’t cheap. It is essential to plan your remodeling ideas ahead of time. Then, hire a remodeling contractor for the job. Ask questions, set realistic expectations, get accurate cost estimates and budgeting from the start. Also spend time learning how to work with a bathroom contractor.
To begin, rip the top and side jambs to the thickness of the wall framing plus the exterior wall sheathing. The cement board will lap over the jambs. The windowsill should also be flush with the interior framing, but hang over the outside sheathing about 1-1/2 in. and have a 5-degree slope toward the outside to help shed water. To keep water from running behind the siding as it drips off the edge, cut a shallow groove (or saw kerf) in the bottom lip (Fig. A). Also, remember to flash behind the trim to keep the window watertight. Trim the window exterior to match the house, using caulk to seal between the trim and siding.
The job of installing our wall-mounted fixtures was tougher than it had to be, thanks to poor and contradictory one-size-fits-all instructions, metric fittings and duplicate and missing mounting parts. Prevent hard-to-fix future problems by test-fitting the actual fixtures when roughing in framing, plumbing and blocking to make sure everything will work out. Then finish the walls. When test-fitting, simulate finished floor and wall surfaces to get the clearances right.

The Home Depot is a great place to buy your bathroom essentials and remodeling materials. We also provide top-rated design and installation services for homeowners across America. Besides undergoing full background checks, our hand-selected remodeling experts are local, licensed and insured. The Home Depot also offers a great selection of flexible finance options.
Interior bathroom demolition costs $1,000 to $2,300. Prices can go higher if you’re removing and moving walls to create a different footprint. For the experienced DIYer, this is a good place to save money by doing it yourself or assisting the contractor. However, demo can get expensive quickly if you take out a load bearing wall, cut electrical lines or break a water pipe. Avoid the risk by hiring a pro.
×