Adequate lighting is needed for all forms of grooming. Include task-specific and ambient, or general, light. Multiple recessed ceiling fixtures are all but invisible and eliminate the locker-room look of a single ceiling-mounted fixture. Include a light fixture above the tub and/or in the shower. Avoid fluorescent lights, which alter the color of your complexion.

Turn off the main water supply to the house, and in a convenient location, cut the hot and cold water supply pipes for the bathroom. Also cut out and remove all the existing water lines and fittings in the bathroom. Finally, cut out and remove the vent section leading to the sink and the main stack 5 in. below the vent tee. Stuff rags into open drain lines to keep sewer gas out of the house.

Last year I bought a house that had the stainless steel micro model installed. The house was surrounded by 80’ tall Maples & Birch. TONS OF LEAVES.Yes, it the micro mesh keeps all leaf and seeds out of the gutter 100%. What the manf and dealers won’t tell you is that you must clean the mesh 2x’s a year to get spring pollen, mold, & fall leaf dust off. Otherwise it will eventually keep EVERYTHING out, including WATER. Major ice problems flowing over the gutters. No it was not the result of ice damming. I removed it all & just deal with the leaves 3x’s each fall.Got ranch home with easy access to the gutters - get the micro mesh. Easier to clean that than clean gunk out of the gutter.hire a young buck to climb a ladder. A whole lot cheaper.
This is great guys! Great work! I'm a retired kitchen guy so I know good work when I see it. I love all of it. My wife and I are doing a Farm kitchen right now as well. Your pictures have me thinking about sending in some before and after of ours. Just like you its the time we get to spend together during the project that makes the whole thing worth while. Great work. I cant say it enough!
Disconnect the trap from the tub, remove any clips, fasteners or screws that hold the tub to the wall, and demolish the old cast iron tub with a sledgehammer. Remove the sink and toilet. Turn off the electricity at the main panel and remove light fixtures. Cap the wires with wire connectors. Then rip out the wall finishes and surfaces clean down to the studs and pull out any insulation. If your ceiling is in good shape, use a utility knife to cut the drywall along the edges so the wall materials will separate cleanly from the ceiling.
Preassemble the shower valve by soldering copper nipples and the shower supply pipe to male adapters and screwing them into the shower valve before fastening the valve to the blocking. That way you won’t damage the valve with heat from the soldering torch. Mount the valve 36 in. above the floor. You can mount the showerhead at any height, but plumbers typically mount them 6 ft. 6 in. above the floor.
I acknowledge that The Home Depot is partnering with me to participate in this Delta UPstile Program (the “Program”). As a part of the Program, I am receiving compensation in the form of products and services, for the purpose of promoting The Home Depot. All expressed opinions and experiences are my own words. My post complies with the Word Of Mouth Marketing Association (WOMMA) Ethics Code and applicable Federal Trade Commission guidelines.
A one-piece shower pan is the key to a leakproof shower. We opted for an easily installed fiberglass shower pan. Forty-eight inch wide pans are common and will work well; 60-in. units like we used must be special-ordered. The shower pan has to fit into the space left by the removed bathtub. Most bathtubs are 60 in. long, perfect for a 60-in. shower base.
Adequate lighting is needed for all forms of grooming. Include task-specific and ambient, or general, light. Multiple recessed ceiling fixtures are all but invisible and eliminate the locker-room look of a single ceiling-mounted fixture. Include a light fixture above the tub and/or in the shower. Avoid fluorescent lights, which alter the color of your complexion.
Turn off the main water supply to the house, and in a convenient location, cut the hot and cold water supply pipes for the bathroom. Also cut out and remove all the existing water lines and fittings in the bathroom. Finally, cut out and remove the vent section leading to the sink and the main stack 5 in. below the vent tee. Stuff rags into open drain lines to keep sewer gas out of the house.
Although this new bathroom is a bit smaller because of additional plumbing walls, it appears larger. Substituting a shower for the bathtub, adding a large mirror, and using a wall-hung sink and toilet all contribute to the spacious feeling. This big-picture stuff is striking, but it’s the step-by-step details that make this small bathroom remodel work. We cover the little kernels of information that will help your project go more smoothly and with fewer headaches.
×