An upscale bathroom remodel may include structural changes like expanding or adjusting the layout. Finishes include things like large ceramic floor tile, heated floors, high-end faucets, new lighting, and stone countertops with double sinks. Showers may have frameless glass doors, rain shower fixtures, shower niches and tiled shower walls. Freestanding tubs are also found in this type of bathroom remodel.


Pedestal sinks can saver or waste space depending on the arrangement and storage options of your bathroom. If you want to open up floor space, they’re an excellent choice. However, they don’t offer the storage that vanity cabinets provide. If your bathroom lacks storage but you have your heart set on a pedestal sink, include open shelves or a tile-lined niche behind or adjacent to it. Alternatively, consider using cabinetry 16 or 18 inches deep, instead of the usual 21 inches, to maximize your floor plan.
If your room is wider than the shower base, fur in the walls as needed to butt against the ends of the shower base (see Photo 14). Our bathroom is 6 ft. wide, so we added a floor-to-ceiling 2×6 wall at the showerhead end and a shorter 2×6 wall at the opposite end. We made that wall only 43 in. above the floor so we could use the top of the wall to hold shampoo and other shower supplies. The shower base usually comes with a special 2-in. drain fitting that you connect to the drain line (Fig. B).
Don't settle for a wimpy flusher. Maximum Performance testing (MaP) gauges a toilet's ability to get the job done with just one push of the handle. Look for a loo with a MaP score of 500 or higher; this group includes many WaterSense-rated toilets, high-efficiency models that use as little as half of the 1.6-gallon-per-flush legal limit. Go to map-testing.com for more info.
This story shows you how to make your small, cramped bathroom more convenient, elegant and easy to clean. These projects make the typical 6 x 8 ft. bathroom feel larger and more comfortable. We'll walk you through the steps for getting more natural light in your shower, replacing your dingy old bathtub with a spacious shower, and installing a toilet and sink that simplify cleaning. So stop dealing with an outdated bathroom and get to work!
The wall-hung toilet’s supply line must have a male adapter with a temporary galvanized cap. Check the instructions on the toilet to get the proper location. Routing water supply lines is different in every bathroom, so you’ll have to adapt runs to your situation. But run the plastic drain lines and vents before starting any supply work. It’s much easier to route water supply lines around drain lines than to route drains and vents around supply lines. The same thinking applies to electrical work: Wait until the water supply work is finished before wiring.
Proper ventilation will prevent moisture from getting trapped in the bathroom, which can lead to mold and mildew growth. Extract moisture by installing a ducted exhaust fan on a timer. Most timers allow you to set the fan for 15 to 60 minutes to remove heat, steam and condensation. Choose a fan according to the cubic feet per minute of air it moves.

Proper ventilation will prevent moisture from getting trapped in the bathroom, which can lead to mold and mildew growth. Extract moisture by installing a ducted exhaust fan on a timer. Most timers allow you to set the fan for 15 to 60 minutes to remove heat, steam and condensation. Choose a fan according to the cubic feet per minute of air it moves.


A full bath requires a minimum of 36 to 40 sq. ft. The finished room must measure at least 5 ft. in one direction to accommodate a tub. Building codes typically require 32x32 in. (finished dimensions) for a shower; if you have the space, larger is better. Just make sure the shower is large enough so you can comfortably raise your arms and bend over in the space.
Using the ultra-trendy animal skull as a main focus point, this space definitely stands out from the rest of the usual white and boring contemporary bathrooms. Notice how the tiny, delicate bare branch echoes and contrasts the strong antlers on the wall, and how the pendant light hangs right in the middle of the negative space provided by the antlers.

Proper ventilation will prevent moisture from getting trapped in the bathroom, which can lead to mold and mildew growth. Extract moisture by installing a ducted exhaust fan on a timer. Most timers allow you to set the fan for 15 to 60 minutes to remove heat, steam and condensation. Choose a fan according to the cubic feet per minute of air it moves.

A full bath requires a minimum of 36 to 40 sq. ft. The finished room must measure at least 5 ft. in one direction to accommodate a tub. Building codes typically require 32x32 in. (finished dimensions) for a shower; if you have the space, larger is better. Just make sure the shower is large enough so you can comfortably raise your arms and bend over in the space.


Tear out the existing piping (Photos 5 and 6). Then frame the 2×6 walls that will contain the new plumbing and the opposite end of the shower base (Photos 8, 9 and 14). It’s easiest to nail the bottom plate to the floor and the top plate to the ceiling, then fill in the studs one at a time by toenailing them in at the top and bottom. Stack the studs directly in front of the old ones wherever possible. Space the studs in the center of the shower about 12 in. apart to leave room for the shower valve and showerhead. The studs behind the toilet should be spaced exactly 19-3/4 in. apart for securing this toilet chair carrier (Photos 8 and 15).

Choose the main color theme for your bathroom, but it should depend on the existing color of the wall. For example, for white colors, apply the white color on all over the walls and furniture. But to keep the contrast, apply a bit darker color for your flooring. You can do it by having a cheaper tile stamp to get the floral or another exciting pattern.

Disconnect the trap from the tub, remove any clips, fasteners or screws that hold the tub to the wall, and demolish the old cast iron tub with a sledgehammer. Remove the sink and toilet. Turn off the electricity at the main panel and remove light fixtures. Cap the wires with wire connectors. Then rip out the wall finishes and surfaces clean down to the studs and pull out any insulation. If your ceiling is in good shape, use a utility knife to cut the drywall along the edges so the wall materials will separate cleanly from the ceiling.


An upscale bathroom remodel may include structural changes like expanding or adjusting the layout. Finishes include things like large ceramic floor tile, heated floors, high-end faucets, new lighting, and stone countertops with double sinks. Showers may have frameless glass doors, rain shower fixtures, shower niches and tiled shower walls. Freestanding tubs are also found in this type of bathroom remodel.

Tear out the existing piping (Photos 5 and 6). Then frame the 2×6 walls that will contain the new plumbing and the opposite end of the shower base (Photos 8, 9 and 14). It’s easiest to nail the bottom plate to the floor and the top plate to the ceiling, then fill in the studs one at a time by toenailing them in at the top and bottom. Stack the studs directly in front of the old ones wherever possible. Space the studs in the center of the shower about 12 in. apart to leave room for the shower valve and showerhead. The studs behind the toilet should be spaced exactly 19-3/4 in. apart for securing this toilet chair carrier (Photos 8 and 15).
Bathroom remodels provide 60 to 70 percent resale returns as a home improvement project. However, this project isn’t cheap. It is essential to plan your remodeling ideas ahead of time. Then, hire a remodeling contractor for the job. Ask questions, set realistic expectations, get accurate cost estimates and budgeting from the start. Also spend time learning how to work with a bathroom contractor.
×