I acknowledge that The Home Depot is partnering with me to participate in this Delta UPstile Program (the “Program”). As a part of the Program, I am receiving compensation in the form of products and services, for the purpose of promoting The Home Depot. All expressed opinions and experiences are my own words. My post complies with the Word Of Mouth Marketing Association (WOMMA) Ethics Code and applicable Federal Trade Commission guidelines.
Low-flow toilets, which use 1.6 gallons of water per flush, are required by law in all new and remodeled baths. Pressure-assisted toilets effectively clear the bowl with one flush, but make considerable noise in the process. Gravity models sometimes require two flushes to clean the bowl properly. For maximum efficiency, choose a bowl with a large water surface. Make sure there's sufficient space around the toilet for comfortable access—ideally, at least 16 inches from the centerline of the toilet and walls or fixtures on either side. Also allow at least 30 inches from the front of the toilet to the nearest object.
There is nothing better than getting into a hot shower at the end of a long day. My husband and I have been wanting to do some remodeling to our master bathroom and I would love to have any one of these designs. They look so functional for their size and I love the shower doors in some of these designs! These have given me some great ideas, thanks for sharing!
This is great guys! Great work! I'm a retired kitchen guy so I know good work when I see it. I love all of it. My wife and I are doing a Farm kitchen right now as well. Your pictures have me thinking about sending in some before and after of ours. Just like you its the time we get to spend together during the project that makes the whole thing worth while. Great work. I cant say it enough!

Although this new bathroom is a bit smaller because of additional plumbing walls, it appears larger. Substituting a shower for the bathtub, adding a large mirror, and using a wall-hung sink and toilet all contribute to the spacious feeling. This big-picture stuff is striking, but it’s the step-by-step details that make this small bathroom remodel work. We cover the little kernels of information that will help your project go more smoothly and with fewer headaches.
Preassemble the shower valve by soldering copper nipples and the shower supply pipe to male adapters and screwing them into the shower valve before fastening the valve to the blocking. That way you won’t damage the valve with heat from the soldering torch. Mount the valve 36 in. above the floor. You can mount the showerhead at any height, but plumbers typically mount them 6 ft. 6 in. above the floor.
If your room is wider than the shower base, fur in the walls as needed to butt against the ends of the shower base (see Photo 14). Our bathroom is 6 ft. wide, so we added a floor-to-ceiling 2×6 wall at the showerhead end and a shorter 2×6 wall at the opposite end. We made that wall only 43 in. above the floor so we could use the top of the wall to hold shampoo and other shower supplies. The shower base usually comes with a special 2-in. drain fitting that you connect to the drain line (Fig. B).

A one-piece shower pan is the key to a leakproof shower. We opted for an easily installed fiberglass shower pan. Forty-eight inch wide pans are common and will work well; 60-in. units like we used must be special-ordered. The shower pan has to fit into the space left by the removed bathtub. Most bathtubs are 60 in. long, perfect for a 60-in. shower base.

Adequate lighting is needed for all forms of grooming. Include task-specific and ambient, or general, light. Multiple recessed ceiling fixtures are all but invisible and eliminate the locker-room look of a single ceiling-mounted fixture. Include a light fixture above the tub and/or in the shower. Avoid fluorescent lights, which alter the color of your complexion.


Time to jump into your DIY pants. I am going to start off with the easiest and most prevalent DIY project around the house. Believe it or not, new paint can transform your bathroom from 1980s drab to 2010s fab. Whether you go bold with dark blue or casual with stripes, new paint will not only give new life to an outdated bathroom, but make it feel larger as well.
The wall behind the toilet can be almost any height. For a standard toilet height of 15 in., make the wall a minimum height of 43 in. If you’d like a higher toilet, make the wall that much higher. Or, make the wall go all the way to the ceiling. We built a short wall to conserve space and to create a shelf and a mirror alcove. The wall at the opposite end of the shower can be any height as well. We made it the same height as the toilet/sink wall so we could line up the accent tile and make a convenient shower shelf.

Turn off the main water supply to the house, and in a convenient location, cut the hot and cold water supply pipes for the bathroom. Also cut out and remove all the existing water lines and fittings in the bathroom. Finally, cut out and remove the vent section leading to the sink and the main stack 5 in. below the vent tee. Stuff rags into open drain lines to keep sewer gas out of the house.
×